Roland DIF-AT24 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Roland DIF-AT24. Roland DIF-AT24 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 17
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Owner’s Manual
The DIF-AT24 lets you transfer up to 8 channels of 24-bit
digital audio data between an R-BUS device and a device
equipped with an ADAT interface.
Congratulations on your purchase of the Roland DIF-AT24.
Before using this unit, carefully read the sections entitled: “USING
THE UNIT SAFELY” (p. 2, 3) and “IMPORTANT NOTES” (p. 4).
These sections provide important information concerning the proper
operation of the unit. Additionally, in order to feel assured that you
have gained a good grasp of every feature provided by your new unit,
Owner’s Manual should be read in its entirety. The manual should be
saved and kept on hand as a convenient reference.
Main Features
* ADAT is a registered trademark of Alesis Corporation.
* All product names mentioned in this document are trademarks or registered
trademarks of their respective owners.
Copyright © 2003 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
Roland Web Site: http://www.roland.co.jp
Zobrazit stránku 0
1 2 3 4 5 6 ... 16 17

Shrnutí obsahu

Strany 1 - Owner’s Manual

Owner’s Manual The DIF-AT24 lets you transfer up to 8 channels of 24-bit digital audio data between an R-BUS device and a device equipped with an ADA

Strany 2 - USING THE UNIT SAFELY

10Connections and settingsConnectionexample 2Connecting the VS-2400CD and a computerHere's an example of synchronization with computer-based sequ

Strany 3 - For Canada

11Connections and settings Sampling Frequency settingsSet the sampling frequency of your sequencer software and the VS-2400CD to the same setting (44

Strany 4 - IMPORTANT NOTES

12Connections and settingsConnectionexample 3Connecting the VS-2400CD and an ADAT deviceThis example allows digital audio signals to be transferred. M

Strany 5 - Contents

13Connections and settingsConnectionexample 4Connecting the VS-2400CD with an ADAT device and BRCThe BRC is used to operate the VS-2400CD and ADAT dev

Strany 6 - Panel descriptions

14Connections and settings Sampling Frequency settingsSet the sampling frequency of the VS-2400CD and ADAT device to the same setting (48 kHz). Mast

Strany 7 - Turning the power on/off

15Connections and settingsConnectionexample 5Using the DIF-AT24 as an additional MIDI OUT for the MV-8000Make connections as shown in the diagram.To p

Strany 8 - Connections and settings

03454012 ’03-11-1KSThis owner’s manual is printed on recycled paper.InformationWhen you need repair service, call your nearest Roland Service

Strany 9

03564056 ’03-11-1KSVM-7100/7200 と接続する場合VM-7100/7200 のシステム・バージョンが 1.7 未満の場合、DIF-AT24 は正常に動作しません。以下の方法で VM-7100/7200 のバージョンを確認し、必ず 1.7 以降にバージ

Strany 10 - Connection

2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual...

Strany 11 - Settings

3 104 • Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children

Strany 12

4 IMPORTANT NOTES In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: 291a Power Supply 3

Strany 13

5 Contents Main Features...1USING

Strany 14

6 Panel descriptions Front Panel ADAT indicator This indicator will light green if an ADAT interface signal is being input to the ADAT digital IN con

Strany 15

7 Turning the power on/off Turning the power on Before you turn each device on, make sure that all devices are connected correctly.Once the connecti

Strany 16 - Information

8 Connections and settings Connectionexample 1 Connecting the VS-2400CD and a computer Here's an example of synchronization with computer-based

Strany 17 - VM-7100/7200 と接続する場合

9 Connections and settings Sampling Frequency settings Set the sampling frequency of your sequencer software, the VS-2400CD, and the UA-1000 to the

Komentáře k této Příručce

Žádné komentáře