Roland LEC-540 Průvodce nastavením Strana 1

Setup GuideRead this rst.This describes the setup tasks and important conditions about the installation location that must be met in order to enable

To Ensure Safe Use8Warning labels are afxed to make areas of danger immediately clear. The meanings of these labels are as follows. Be sure to heed

9 Pour utiliser en toute sécuritéLa manipulation ou l'utilisation inadéquates de cet appareil peuvent causer des blessures ou des dommages matéri

Pour utiliser en toute sécurité10 L'utilisation incorrecte peut causer des blessures ATTENTIONS'assurer de suivre les procédures d'uti

Pour utiliser en toute sécurité11 ATTENTIONBrancher à une prise électrique conforme aux caractéristiques de cet appareil (ten-sion, fréquence et cour

Pour utiliser en toute sécurité12 ATTENTIONManipuler le câble d'alimentation, la che et la prise électrique correctement et avec soin.Ne jamais

Pour utiliser en toute sécurité13 Remarques importantes à propos du câble d'alimentation, de la che et de la prise électriqueNe jamais déposer

Pour utiliser en toute sécurité14 L'encre, les liquides nettoyants et les liquides usées sont inam-mables et toxiques En cas d'ingestion o

Pour utiliser en toute sécurité15 Cet appareil utilise des rayons ultraviolets. Attention : Rayonnement ultravioletCet appareil est muni de couvercle

Pour utiliser en toute sécurité16Des vignettes d'avertissement sont apposées pour qu'il soit facile de repérer les zones dangere-uses. La s

Setup Guide17

Thank you very much for purchasing this product. To ensure correct and safe usage with a full understanding of this product's performance, pleas

181. Installation EnvironmentDeciding On an Installation SiteInstall in a quiet, stable location oering good operating conditions. An unsuitable loca

1. Installation Environment19Temperature and HumidityMaintain the specied temperature and humidity even when the machine is not in use. If temperatur

202. Included ItemsThe following items are packed together with the unit. Make sure they are all present and accounted for.Stand stay (1)Dancer roller

2. Included Items21Hexagonal wrench (5 mm) (1)Blade holder/Blade/Pin (1 of each)Replacement blades for separating knife (1)Head-unit tool (1)Cartridge

2. Included Items22Air intake box (1)

233. Assembling and InstallingStep 1: Assemble the StandCAUTION Unpacking and installation must be carried out by six or more persons.Otherwise the ma

3. Assembling and Installing24 Loosely tighten the bolts in the 8 locations shown in the gure. Fully tighten all the loosely-tightened bolts.w Lower

3. Assembling and Installing252.Attach the Rail Slider and the Arm to the Stand Legs. Attach the arm to the rail slider. Secure the arm with the arm

3. Assembling and Installing263.Attach the dancer roller to the stand legs.Remove the packing material at the location shown in the gure. Align the

3. Assembling and Installing274.Attach the paper tube.Pull the dancer roller back toward you. Loosen the arm retaining screw. Set the paper tube on

1ContentsCompany names and product names are trademarks or registered trademarks of their respective holders.http://www.rolanddg.com/Copyright © 2010-

3. Assembling and Installing28Step 2: Mount the MachineCAUTION Unpacking and installation must be carried out by six or more persons.Otherwise the mac

3. Assembling and Installing29Step 3: Installing the Media HolderProcedure Place the shafts on the stand. Pass the media holder (left) through the f

3. Assembling and Installing30 Move the Right media holder to the left side of the shafts.Pass it through from the right edge (as seen from the back

3. Assembling and Installing31Step 4: Attach the Rear CoverProcedureSecure the left and right rear-cover stays in place with the screws.Use a commerc

3. Assembling and Installing32Step 5: Attach the Media GuideProcedureMove the dancer roller toward the rear.Remove the screws at the both ends.Use a

3. Assembling and Installing33wLoosen the screws near the center (in 2 locations).Hook the media guide on the loosened screws.Tighten the screws.The

3. Assembling and Installing34Step 6: Attach the Air Intake BoxCAUTION The air intake box is as heavy as 20kg. When handling it, be sure to have two o

3. Assembling and Installing35wRemove the packing materials.Secure the air intake box with bolts.Start with the bolts on the air intake box stay (rig

3. Assembling and Installing36Step 7: Install the Drain BottleRemove the drain-tube cover and attach the bottle stand. Attach the drain-tube cover to

3. Assembling and Installing37wFrom the back of the machine, attach the drain bottle.At the location shown in the gure, secure in place the part you

2 To Ensure Safe UseImproper handling or operation of this machine may result in injury or damage to property. Points which must be observed to preven

3. Assembling and Installing38Step 8: Remove the Packing MaterialsTape and other packing materials are attached to the machine to protect it from vibr

394. Connecting the CablesConnecting the Cable of the Take-up UnitPeel off the tape.Pass the take-up unit cable through at the locations shown in th

4. Connecting the Cables40Connecting the Power Cord and the Network CableWARNING Connect to electrical outlet that complies with this machine's r

415. Installing the Ink CartridgesInk ModeFor LEC-540, the ink mode must be selected based on the types of ink to be used. P. 43 "Selecting the

5. Installing the Ink Cartridges42At the locations shown in the gure, afx the cartridge-slot labels matching the se-lected ink mode.Ink modeECO-UV

5. Installing the Ink Cartridges43Selecting the Ink ModeBe sure to make the selection of the ink mode when switching on the power for the rst time.Pr

5. Installing the Ink Cartridges44Press .The sub power switches o automatically.This completes selection of the ink mode. Go on to the next step, &

5. Installing the Ink Cartridges45Installing the Ink CartridgesDuring cleaning, you need to insert and remove cartridges several times. The on-screen

5. Installing the Ink Cartridges462.Clean the print heads using the SOL INK cleaning cartridge.Check the selected ink mode.<When the selected ink

5. Installing the Ink Cartridges47When this screen appears, pull out the SOL INK cleaning cartridges.When this screen appears, cleaning is nished.M

To Ensure Safe Use3 Incorrect operation may cause injury WARNINGBe sure to follow the operation proce-dures described in this documentation. Never al

5. Installing the Ink Cartridges48wClose the ink cartridge cover.Make sure the drain bottle is installed.Press.When this screen appears, lling with

496. Installing the BladeCAUTION Be sure to perform operations as specied by these instructions, and never touch any area not specied in the instr

6. Installing the Blade503.Install the blade holder.Loosen the screw shown in the gure.Support the screw from below and insert the blade holder.If

517. Network SettingsIntroductionThis machine has a built-in print server as a network interface. When you use the print server, you can send output d

7. Network Settings52wClick [Properties].If you're using Windows Vista click [Allow] when the [User Account Control] dialog box appears.The [Loca

7. Network Settings53Step 2: Make the Network Settings on the PrinterImportantThe addresses used in this section are merely example settings. For deta

7. Network Settings54wUse to select the address number.[SUBNET MASK]: 255.255.255.000Note: For the subnet mask, make the setting the same value as the

7. Network Settings55Step 3: Make the Port Settings for the Software RIP The settings for the software RIP will be made here. For the output destinat

568. Installation of Ventilating EquipmentVentilating EquipmentIn preparing ventilating devices, please note the following points. You will be requir

8. Installation of Ventilating Equipment57wAttach the hose to the connection port on the unit.Insert all the way.Connecting port: Diameter of 38 mm

To Ensure Safe Use4 WARNINGConnect to an electrical outlet that com-plies with this machine's ratings (for voltage, frequency, and current).Inco

589. When Not in Use for a Prolonged PeriodKeep Performing MaintenanceSwitch on the power once every two weeks.Switch on the sub power once every two

5910. When Moving the UnitProcedures from Preparing to Move Through ReinstallingTo move the machine, you must completely drain all ink inside the mach

10. When Moving the Unit60WARNING Never put discharged uid or ink closed to re.Doing so may cause the blaze.CAUTION To store discharged uid tempora

R2-120718

To Ensure Safe Use5Never place any object on top or subject to damage.Never bend or twist with undue force.Never pull with undue force.Never bundle,

To Ensure Safe Use6 Ink, cleaning uid, and discharged uid are ammable and toxic In the event of ingestion or physical distress In the event of co

To Ensure Safe Use7 This machine weighs 300 kg (661 lb.). Media weighs 30 kg (66 lb.). WARNINGInstall the machine in a location that is level, stable